PHP Manual: SNMP::set

Description

public function SNMP::set(array|string $objectId, array|string $type, array|string $value): bool

Requests remote SNMP agent setting the value of one or more SNMP objects specified by the objectId.

Parameters

If objectId is string, both type and value must be string too. If objectId is array value must be equal-sized array containing corresponding values, type may be either string (it's value will be used for all objectId-value pairs) or equal-sized array with per-OID value. When any other parameters' combinations are used, a number of E_WARNING messages may be shown with detailed description.

objectId

The SNMP object id

When count of OIDs in object_id array is greater than max_oids object property set method will have to use multiple queries to perform requested value updates. In this case type and value checks are made per-chunk so second or subsequent requests may fail due to wrong type or value for OID requested. To mark this a warning is raised when count of OIDs in object_id array is greater than max_oids.

type

The MIB defines the type of each object id. It has to be specified as a single character from the below list.

**types**
=	The type is taken from the MIB
i	INTEGER
u	INTEGER
s	STRING
x	HEX STRING
d	DECIMAL STRING
n	NULLOBJ
o	OBJID
t	TIMETICKS
a	IPADDRESS
b	BITS

If OPAQUE_SPECIAL_TYPES was defined while compiling the SNMP library, the following are also valid:

**types**
U	unsigned int64
I	signed int64
F	float
D	double

Most of these will use the obvious corresponding ASN.1 type. 's', 'x', 'd' and 'b' are all different ways of specifying an OCTET STRING value, and the 'u' unsigned type is also used for handling Gauge32 values.

If the MIB-Files are loaded into the MIB Tree with "snmp_read_mib" or by specifying it in the libsnmp config, '=' may be used as the type parameter for all object ids as the type can then be automatically read from the MIB.

Note that there are two ways to set a variable of the type BITS like e.g. "SYNTAX BITS {telnet(0), ftp(1), http(2), icmp(3), snmp(4), ssh(5), https(6)}":

Using type "b" and a list of bit numbers. This method is not recommended since GET query for the same OID would return e.g. 0xF8.
Using type "x" and a hex number but without(!) the usual "0x" prefix.

See examples section for more details.

value

The new value.

Return Values

Returns true on success or false on failure.

Errors/Exceptions

Throws an SNMPException if a library error occurs and its type is included in the SNMP::$exceptions_enabled bitmask. Otherwise, emits an E_WARNING.

Examples

Example #1 Set single SNMP object id

<?php
  $session = new SNMP(SNMP::VERSION_2C, "127.0.0.1", "private");
  $session->set('SNMPv2-MIB::sysContact.0', 's', "Nobody");
?>

Example #2 Set multiple values using single SNMP::set() call

<?php
  $session = new SNMP(SNMP::VERSION_2C, "127.0.0.1", "private");
  $session->set(array('SNMPv2-MIB::sysContact.0', 'SNMPv2-MIB::sysLocation.0'), array('s', 's'), array("Nobody", "Nowhere"));
// or
  $session->set(array('SNMPv2-MIB::sysContact.0', 'SNMPv2-MIB::sysLocation.0'), 's', array("Nobody", "Nowhere"));
?>

Example #3 Using SNMP::set() for setting BITS SNMP object id

<?php
  $session = new SNMP(SNMP::VERSION_2C, "127.0.0.1", "private");
  $session->set('FOO-MIB::bar.42', 'b', '0 1 2 3 4');
// or
  $session->set('FOO-MIB::bar.42', 'x', 'F0');
?>

SNMP::set

Description

Parameters

Return Values

Errors/Exceptions

Examples

See Also